The magazine system comprises of :-
1 x Magazine assembly.
1 x Mounting bracket.
1 x Pellet tray
1 x 3mm allen key
1 x Fitting instructions.
The .177magazine is compatible with most waisted diablo pellets.
The .22 magazine will handle most pellets under 8.75mm long.
The pellet tray is a formed piece of aluminium that improves the transfer of the pellet in to the .177 breech by the bolt for both single and multi shot configurations.
This is not required for .22 magazines.
Magazine in use. Video
    Close up photo of Magazine Notes: Both bracket types (15.0mm & 13.0mm) will require a minimum of 15.0mm gap between the top of the dovetail and the bottom of your scope.
Please check. Medium mounts with most types of scope are normally sufficient.
See the drawing here for instructions where to measure to determine the size of bracket you need to suit your rifle.
See the notes on choosing Right or Left Fitting magazines.
Photo comparing Left and Right fitting .177 magazines Click Photo comparing Left and Right fitting .22 magazines   Click
Single Shot Loader for Air Arms S410 S510 S510T
.177 Calibre
Single Shot Loader.177 Cal
£56.95
.22 Calibre
Single Shot Loader.22 Cal
£56.95
Popup blockers may prevent the video above from showing.
Click on 'allow blocked content' at the top of your browser page.
Single Shot Loader on S510
The loader clips on to the rifle using the same method as as the
Air Arms magazines. Cocking the rifle pops open the loader for
the next pellet. The loader will fit all Air Arms multi-shot
rifles that use the standard Air Arms Magazine (except Galahad)
Accepts .177 pellets up to 7.5mm long & .22 up to 8.5mm long.
If the standard AirArms magazine fits under the scope the
single shot loader will fit too with an extra 3mm clearance.
Adjustable Butt Pad Mounting Kit for S400 & S400F
£72.95
Please check your stock dimensions.
The stock should be approximately 1mm smaller in overall
height and width than the plate dimensions shown
in the drawing.
The kit contains the necessary hardware to re-fit the existing pad
to give vertical adjustment. Details for fitting can be read here. There is 5mm of upward and 40mm of downward adjustment.
S510 Air Stripper and Carbon Sleeve Set. Fits standard S510 Ultimate Sporter. (Not FAC)
S510 Natural Aluminium Stripper.
£96.95
S510 Black Anodised Stripper.
£98.95
S510 Barrel Adaptor and Carbon Sleeve Set. Fits standard S510 Ultimate Sporter. (Not FAC)
S510 Natural Aluminium Adaptor.
£82.95
S510 Black Anodised Adaptor.
£84.95
S510 Air Stripper and Carbon Sleeve Set. CNC machined from 6082 aluminium and finished
Natural aluminium or black anodised.
Replaces the existing barrel shroud and allows the use of a airstripper.
A supporting collar screws on to the action to support the carbon sleeve
at the breech end of the barrel. O-rings fitted to the stripper and support
collar provide a snug fit to the carbon sleeve.
A compatible airstripper is also available.
S510 Barrel Adaptor and Carbon Sleeve Set. Replaces the existing barrel shroud and allows the use of a silencer.
The 1/2" unf barrel adaptor is fitted to the barrel to provide
good concentricity and eliminates the issues of 'clipping' when fitting
silencers to the factory shroud.
A supporting collar screws on to the action to support the carbon sleeve
at the breech end of the barrel. O-rings fitted to the stripper and support
collar provide a snug fit to the carbon sleeve.
A compatible airstripper is also available.
Please note these items do not fit FAC rifles.
Please check the position of the barrel.
Typically the end of the barrel is 46.0mm in front of the filling cap.
Please contact us if the barrel position is different to the drawing above.
Air Stripper .177 Calibre. Natural Aluminium for S400 & S410
.177 Calibre
Natural Aluminium Body
£61.95
Air Stripper .177 Calibre. Black Anodised for S400 & S410
.177 Calibre
Black Anodised Aluminium Body
£62.95
Air Stripper .22 Calibre. Natural Aluminium for S400 & S410
.22 Calibre
Natural Aluminium Body
£61.95
Air Stripper .22 Calibre. Black Anodised for S400 & S410
.22 Calibre
Black Anodised Aluminium Body
£62.95
Air Strippers for Air Arms S400 & S410 Rifles with 10.0mm mounting diameter. The air strippers come with the choice of a natural, black anodised or brass cone.
Larger photo of Air Stripper fitted on a S400 rifle.
The cone has 8mm forwarard / backwards adjustment.
Air Stripper .177 Calibre. Natural Aluminium for MPR 14.0mm Barrel
.177 Calibre
Natural Aluminium Body 14.0mm MPR Barrel
£61.95
Air Stripper .177 Calibre. Black Anodised for for MPR 14.0mm Barrel
.177 Calibre
Black Anodised Aluminium Body 14.0mm MPR Barrel
£62.95
Air Strippers for Air Arms MPR and Rifles with 14.0mm barrel diameter. The air strippers come with the choice of a natural, black anodised or brass cone.
The cone has 8mm forwarard / backwards adjustment.
A selection of Air Strippers
with 1/2" UNF fitting are also available.
Air Strippers for barrels with 1/2" UNF male screw thread.
Order by Post Click here.
Adjustable Triggers for S400 S400F S410 S500 & S510
Adjustable Trigger Natural Aluminium.
Natural Aluminium
£58.95
Adjustable Trigger Black Anodised Aluminium.
Black Anodised
£59.95
Adjustable Trigger Brass
Brass
£62.95
Please see the information here regarding clearance of the trigger guard.
Adjustable Trigger for Air Arms S400 S400F S410 S500 & S510 Rifles. The trigger kit comprises of :-
1 x trigger assembly.
1 x 2.0mm allen key
1 x 1.5mm allen key
1 x Fitting instructions.
Please see the information here regarding clearance of the trigger guard.
S400 & S410 Setback Trigger Blade. The setback is approximately 6.0mm compared to the standard blade.
A safety button is not fitted due to space limits.
S400 / S410 Hamster - with magazine recess.
£55.95
Please e-mail for ordering details if fitting to Air Arms Walnut stock
or other custom stocks.
S400 / S410 Hamster - without recess.
£55.95
S400 / S410 Aluminium Hamster -
Aluminium Hamster. No recess
£77.95
CNC machined in black delrin with aluminium support posts.
Dimension from barrel centre line to base of hamster plate is approx. 125mm.
An optional recess machined in the top face with a magnet fitted to 'store' a Rowan magazine.
The posts are black anodised aluminium.
Rear post is 31.0mm long & front post 38.0mm long.
Fitting requirments:-
The rear post utilises the existing stock retaining screw position, with a new longer screw supplied.
The stock will require 1 new 6.0mm hole drilling to fit the front post.
Kit includes mounting fasteners, allen key and fitting instructions.
S400 MPR Hamster.
£55.95
Aluminium
£77.95
If you wish to make payment by cheque, please see Ordering by Post
CNC machined in black delrin with aluminium support posts.
Dimension from barrel centre line to base of hamster plate is approx. 140mm.
Posts are black anodised aluminium and attaches to the factory fitted threaded
bushes on the underside of the rifle.
Kit includes mounting fasteners and allen key.
Please check that there are 2x threaded bushes fitted
to the underside of the stock.
Click for photo showing threaded bushes.
S400 MPR Butt Pad Spacer.
£66.95
Additional Spacers. Supplied in pairs.
£15.95
Please check your stock dimensions.
The stock should be approximately
1mm smaller in overall height
and width than the plate dimensions
shown in the drawing.
The kit contains the necessary
hardware to re-fit the existing pad.
CNC machined in 6082 aluminium with aluminium spacer posts.
Re-uses original butt pad.
Butt spacer overall thickness with 15mm spacers = 27mm
Butt pad overall thickness with 25mm spacers = 37mm
Additional spacers available which can be stacked together to
increase the pad spacing further.
Kit includes mounting fasteners and allen key.
Larger photo of Butt Pad Spacer parts.
S400 MPR Trigger Blades.
Natural Aluminium
£30.95
Black Anodised Aluminium
£31.95
Brass
£32.95
CNC machined in 6082 aluminium or brass.
Replaces the plastic blade supplied as standard.
Fits on to the existing 4mm diameter trigger post.
Larger photo of MPR Blade Click
Bolt Handles for S400 & S410
Black Anodised.
£37.95
Handles available for Air Arms TDR in Ball+Ball only.
Natural Aluminium
£36.95
Brass.
£44.95
Stainless Steel.
£45.95
Precision CNC machined in one piece from high grade bar stock.
Natural aluminium, black anodised, brass and Stainless Steel.
Right hand bolt shown.
Barrel Bands for S400 & S410.       For 12.0mm diameter barrels.
Natural Aluminium.
£35.95
Black Anodised Aluminium.
£36.95
Brass.
£39.95
The greater clearance hole for the barrel allows different 'o' rings
to be fitted to vary the amount of support the barrel has.
Two 'o' rings are supplied give 'firm' and 'medium' barrel support.
The 'o' ring can be removed to allow the barrel to float if required.
Click here for larger photo of the brass barrel band.
Three sizes are available for fitting over
14mm 15mm & 16mm barrels.
Supplied with o-ring.
Filler Cap for S400 & S410.
Natural Aluminium.
£39.95
Replacement Filler Caps for the Air Arms S400 / S410 rifles.
Machined from 6082 aluminium bar.
Caps fit over T-bar filler connectors with M20 thread.
Barrel Sleeves for S400 S410 & MPR
Natural Aluminium.
£23.95
Black Anodised Aluminium.
£24.95
Brass.
£27.95
If you wish to make payment by cheque, please see Order by Post
Add a finishing touch to your rifle.
Simply slide over the barrel and secure with 1 grub screw.
Fits most rifles with 12.0mm barrel and flat front face on breech.
Does not fit rifles with 'rosebud' barrel sleeve.
Available in black anodised aluminium, natural aluminium or brass.